-
0,25 € netto
A distinctive feature of the new GSM Controller is the configuration via the website.
Taught by experience from selling previous versions of GSM Controllers, we know how difficult it can be to configure. Therefore, in the case of the new device, we wanted to reduce this operation to a simple selection on the website, as it is in the case of Lan Controller.
There is no extra cables needed, no driver installation and no special software needed. The customer simply inserts a SIM card, turns on the device, logs into his account and, by entering ID number of his device for the first time, adds it to the list of his devices.
Further settings are made through the configuration page on the mqtt.ats.pl server. The webpage uses the MQTT protocol to communicate with a device that uses GPRS data transmission.
In case the SIM card does not use the default Internet access settings, we provide in the installation procedure how to change the device settings via SMS.
Working modes
- Control by calling from an authorized number (in effect, it will turn on the relay and e.g. open the gate).
- Control and receiving information via SMS.
- Controlling and receiving data via the server using the mqtt protocol.
- Local automation using conditions set on the device that may result in, for example, turning on the output depending on the sensor reading.
GSM Controller can work in all these modes simultaneously!
Mobile application
A simple application for the phone significantly extends the possibilities of using Tinycontrol devices. You can check the reading of a sensor or logic input at any time. Soon it will also be possible to control the outputs.
Hardware
- 2 analog inputs: for the 0-5V and 0-33V range, for measuring voltage, direct current (additional sensors needed), temperature sensors, photoresistors - dusk sensor, pressure sensor and many others.
- Digital input in 1-Wire standard - measurement of up to 8 DS18B20 temperature probes.
- Digital input in I2C standard - for many different sensors or outputs extension.
- Serial bus (UART 3.3V).
- 2 logic inputs - as a status monitor (open/close door, PIR sensors, etc.), as button for manual switching.
- 1 relay (NO, C, NC).
- Measurement of supply voltage and temperature on the board.
Software
- Configuration via the website.
- Support for SMS commands and notifications.
- Changing the output state by making a call from an authorized number.
- Support for up to 100 numbers authorized for the call function.
- Support for HTTP (GET) and MQTT communication protocols.
- Calibration of sensors.
- Calculating the difference of readings from inputs.
List of currently supported sensors and devices
Analog inputs (voltage measurement in the inputs range, others supported in firmware)
- DC current sensors: ACS711EX_15, ACS711EX_30, ACS709_75, ACS711LC_12, ACS711LC_25, ACS711LC20, WCS1800, LA100P, R=0.1Ω, R=0.01Ω, R=0.05Ω
Logical inputs (digital)
- magnetic sensor of door opening, etc.
1-Wire bus
- temperature sensor DS18B20
I2C bus
- humidity sensors: BME280 (humidity, temperature, atmospheric pressure)
- particulate matter sensor SPS30 (PM1, PM2.5, PM4, PM10)
- outputs extension OUT1-4 PCF8574
Serial port
- CO2 sensors MH-Z16, MH-Z19
- Ozone sensor GMQ125
MODBUS port (via an additional RS485 converter)
- 2-way energy meters SDM120M and SDM72D-M (power, energy, voltage, current and other readings depending on the meter)
- Danfos controller EKC 202C
Specification
GSMKON-040 | |
Supply voltage |
5-55V |
Power consumption | 0.2W (temporarily 5W) |
Relay | 125VAC 3A |
Antenna | SMA connector |
SIM card | nano SIM |
Operating temperature range | -20 to +55 °C |
Dimensions | 69 x 40 x 29 mm (without DIN base and antenna) |
Weight | 56g |
Kit contents |
GSM Controller in housing |