-
0,26 $ netto
Mercusys ME50G is a Wi-Fi 5 wireless repeater. It uses IEEE 802.11 b/g/n in 2.4 GHz and IEEE 802.11 a/n/ac in 5 GHz. Thanks to the use of 3x3 MU-MIMO, the maximum theoretical bandwidth is 1900 Mb / s - 600 Mb / s in 2.4 GHz and 1300 Mb / s in 5 GHz. You can connect the ME50G to a network advertised by any device, regardless of manufacturer. The wireless network signal will be properly strengthened, thanks to which the transmission range will increase. An additional advantage is the use of external antennas, which provide better range than competing solutions with built-in antennas.
The offered product has 1 gigabit Ethernet port (10/100/1000 Mbps), to which you can connect devices that do not support Wi-Fi communication. ME50G supports AP (Access Point) mode, using this mode you can create a new independent wireless network.
Wi-Fi 5 AC1900 (3x3 MIMO) wireless network
The device is compatible with Wi-Fi 5 and can operate simultaneously on the 2.4 and 5 GHz bands. It utilizes IEEE 802.11 b/g/n protocols in the 2.4 GHz band and IEEE 802.11 a/n/ac protocols in the 5 GHz band. Through the use of triple polarization (3x3 MIMO), the maximum theoretical throughput is 600 Mb/s in the 2.4 GHz band and 1300 Mb/s in the 5 GHz band. ME50G provides higher speeds than competing solutions using Wi-Fi 5.
Extend your Wi-Fi
The offered product is designed to extend an existing Wi-Fi network. It comes with four high-gain omni-directional external antennas, significantly increasing the coverage area and eliminating dead zones. It utilizes Wi-Fi 5 but is backward compatible with the Wi-Fi 4 standard. It doesn't matter what device you are using as the main router; ME50G can be used with a device from any manufacturer.
Adaptive Path Selection (APS) technology
APS allows for the selection of an optimal route and operating band at any given moment. It ensures the best possible signal, throughput, and latency for a particular user. Individual receivers can be shifted between bands as necessary, eliminating the issue of excessive load on any one band. ME50G is capable of achieving the full throughput offered by the Wi-Fi 5 standard.
Simple configuration
You can perform the configuration using the WPS button located on the side of the casing. Pressing it on both the router and the signal booster will establish the connection. Once the connection is established, the device is ready to use.
On the front of the casing, there is an LED light indicating the quality of the connection. If the LED is shining blue, it means the ME50G is positioned too far from the router, and you should consider changing its location.
Two operation modes
The primary operating mode of the ME50G is as a signal booster (range extender), where the device extends an existing wireless network. It also supports an access point mode, enabling you to create a new network. To do this, you would need to supply the signal through an Ethernet cable, as the ME50G is equipped with a built-in Gigabit port (10/100/1000 Mb/s).
Mercusys app
The Mercusys application is available on mobile devices running Android/iOS systems. It significantly simplifies the configuration of new devices, allowing you to monitor the network status and fully manage it. You can observe the Wi-Fi status in real-time and control which users are connecting to your network.
Specifications
Mercusys ME50G | |
Wireless | |
---|---|
Wireless Standards |
2,4 GHz: IEEE 802.11 b/g/n 5 GHz: IEEE 802.11 a/n/ac |
Frequency |
2,4 GHz, 5 GHz |
WiFi Speeds |
600 Mbps at 2.4GHz, 1300 Mbps at 5GHz |
Reception Sensitivity |
2,4 GHz:
5 GHz: |
Transmission Power |
< 20 dBm |
Wireless Security |
WPA, WPA2, WPA3-PSK |
Hardware | |
Dimensions |
with plug: 84.7×76.3×112 mm without plug: 84.7×39×112 mm
|
Interfaces |
1 Gigabit Ethernet Port |
Button |
WPS / Reset |
Antenna Type |
4× External Antennas |
Power Consumption | 12W |
Others | |
Package Contents | Wi-Fi Range Extender (ME50G) Quick Installation Guide |
Operating Temperature | 0°C~40°C (32°F~104°F) |
Operating Humidity | 10%~90% Non-Condensing |